![]() ![]() Do I need to integrate this back into the RAID configuration somehow?įollow the general install instructions, and it should be fine. I think this last one is a special journal volume, but am not sure what to do with it. After installation 3 separate RAID volumes / filesystems were detected, md0(ext4, 11TB) with all my files, md10(swap) and md50(xfs,500MB). Under ThecusOS this speed was dynamic, based on system temperature, and it would by default spin very slow after boot-up.ģ. The system fan is spinning a bit too loud for my taste. These worked fine under the old 'ThecusOS'.Ģ. Raid access doesn't blink any of the leds that are present in each bay. Go there in your browser and finish setup.Īs of now I only have some minor things to fix, maybe others have some tips how to fix these:ġ. I did this by logging in as root with the password I configured during installation, then ran 'apt install net-tools' after which I could use the trusty ifconfig to see my nic config. Install OMV normally, see docs for details.įor me after install it didn't show the correct network interface configuration, so I had to look up the IP that was configured through DHCP. ![]() Set the installation media USB stick as first boot device in the BIOS. Power up your N5550 and press F2 as soon as you see the prompt.ħ. Connect a monitor to HDMI and a keyboard to USB on the back.Ħ. It's easy to use this port as you can't boot from it, so no USB boot priority issues.ĥ. Insert the USB stick you want to install OMV on in the front. Insert the installation media USB stick in a USB port on the back.Ĥ. This will trigger the shutdown procedure.ģ. Power down your N5550 through the web interface or by pressing the power button once. Build the installation media USB stick from the downloaded ISO, with Balena Etcher.Ģ. I'm surprised to see how easy the process went from downloading the ISO to a fully functioning OMV setup on my NAS If anyone needs a hand in doing the same, let me know, but I'm sure most can figure out the basics:ġ. One for installation media and the other for the OMV OS install. SNMP MIB for ReadyNAS OS 6 devices can be downloaded directly from the management interface by going to System > Settings > SNMP and clicking on the Download MIB button in the SNMP settings pop-up.So I just installed OMV on my Thecus N5550 NAS, using 2 USB sticks. To manually install add-ons for all ReadyNAS devices, download the applicable package from ReadyNAS Apps & Add-ons (For ReadyNAS OS 6 devices, you can use Read圜LOUD - see instructions)Īpps for ReadyNAS OS 6 devices can be downloaded through the management interface by going to Apps > Available Apps. RAIDar is used to discover NETGEAR Storage on your local network. ![]() Secure and direct VPN-like access to your data from your Windows, Mac, iOS or Android device. RAIDiator 4.2 (version 4.2.31) for Pro Pioneer / Pro Business / Pro 2 / Pro 4 / Pro 6 / NVX / Ultra 2 / Ultra 4 / Ultra 6 / Ultra 2 Plus / Ultra 4 Plus / Ultra 6 Plus / 1500 / 2100 / 3100 / 3200 / 4200 RAIDiator 5.3 (version 5.3.13) for DuoV2 / NV+V2 Note: Image downloads are zipped and must be unzipped before being uploaded into your ReadyNAS.ĭownloads for latest ReadyNAS OS 6 devices:Īrm ( Version 6.10.8) for RN102 / RN104 / RN202 / RN204 / RN212 / RN214 / RN2120 You can elect to perform a remote update from your ReadyNAS management interface or you can download the relevant image below and perform a local update. ReadyNAS OS is the software that drives the ReadyNAS devices. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |